Locate the engine code stamped into the engine block. For 6-cylinder engines, check behind the distributor on the right hand, or passenger, side of the block. For 8-cylinders, check behind the water pump on the front of the block. Use a flashlight if necessary. I have a 1958 Chevy shortbed 1/2 ton pick up. I have taken out the engine and I am trying to find out what the engine number means. The casting numbers make sense but the engine vin/ID number doesn't show up any where I have looked. Can anyone help me with this. The number is "FI2. Open the hood. Locate the engine code stamped into the engine block. For 6-cylinder engines, check behind the distributor on the right hand, or passenger, side of the block. For 8-cylinders, check behind the water pump on the front of the block. Small Block Chevy Suffix Codes: HR - TBS. GM body designation.All these are identified here.Quickly, A = Chevelle, F = Camaro, X = Nova. If you're looking at the engine code - this is already known. Decoding the ID numbers on Chevy Smallblock motors: (Info compiled Ray Buck ) Since there are several numbers on the block, we need to identify the ones we're gonna use. The first one I usually use is the block casting number which is located at the back of the driver's side cylinder head and will look something like: 3970010.

Engine Block Casting Numbers

The block casting number on small block and big block Chevrolet V8 motors is located on a ledge found at the rear of the block, most often on the driver's side. This ledge is below the deck of the block and the ledge forms the mating surface between the block and the transmission bell housing.

Block casting #3902406 ~ 396 2-bolt (325hp/350hp) or 4-bolt (375hp) main caps.
Prevailing theory is the letter 'P' indicates the block was destined for passenger car and not a truck.

Block casting #3892657 ~ 327 (275/325hp) 2-bolt main caps.

Cylinder Head Casting Numbers

Engine Assembly Date/Suffix Code:
The engine assembly code looks similar to T0601ED. In this case the first letter 'T' stands for an engine factory Tonawanda, an 'F' or 'V' for Flint or 'K' for McKinnon Industries. The next two digits indicate the month of the year, in this example '06' or the sixth month, June. The '01' indicates the 1st day of the month. So what do we have so far in this example? The motor was assembled at the Tonawanda factory on June 1st. The calendar year itself is not given but remember that the engine assembly had to be manufactured and assembled before the car was built. What we have left is the 'suffix code' which in this example is ED, a 1967 396cid with 325hp. Chevrolet used two letters to code the type, size, and horsepower rating of the engine and the transmission type to be used with that engine.

The final vehicle assembly plant sometimes stamped a CON VIN (CON VIN) on the same machined area as the engine ID code. This stamping wasn't mandated until the 1968 model year but has been found (and not found) on 1967 models. If yours has the CON VIN (and hasn't obviously been re-stamped), you can be sure the engine is original to your Chevelle. The CON VIN might look like 'T0601ED7A123456' stamped into the pad on the front passenger side of the block. In this example, 7A123456 decodes to 1967 model year, Atlanta final assembly, and the serial number of the VIN. Sometimes the CON VIN was stamped into a different area of the block on the flange edge of the rear of the block, near the bell housing mating surface. Sometimes the stamping is found above the timing cover mating surface on the front of the block.

While NOT a hard and fast rule, it has been found that mainly the higher horsepower engines such as the 327/325 RPO L79 and all SS 396 engines have a CON VIN stamping. This CON VIN stamping is usually found on the engine ID pad located on the block in front of passenger side head such as this example.

T0609ED ~ Tonawanda, N.Y., June 9, 1967 ~ 396/325hp w/manual transmission
Note CON VIN stamped at Kansas City final assembly plant.

Mandatory VIN stamping of all engines was not required by federal law until the 1968 model year, actually January 1, 1968.

Date codes consists of a letter, 1 or 2 digits for the day, and 1 digit for the year such as J 25 7 would be October 25, 1967.

The block casting number on small block and big block Chevy V8 motors is located on a ledge found at the rear of the block, most often on the driver's side. This ledge is below the deck of the block and the ledge forms the mating surface between the block and the transmission bellhousing.

12 labours of hercules ii: the cretan bull crack. Slay the Nemean Lion. In the town of Nemea, there was an invincible lion that.

Engine Assembly Date/Suffix Code:
The engine assembly code looks similar to this: T0601ED. In this case the first letter 'T' stands for an engine factory Tonawanda Engine Plant, either 'F' or 'V' would indicate Flint, MI., 'K' is used for McKinnon Industries while 'S' is used for Saginaw Service. The next two digits stand for the month of the year. In this example '06' or the sixth month, June. The '01' stands for the 1st day of the month. Sometimes (but not always) the letter 'I' is substituted for the number '1'.

So what do we have so far in this example? The motor was assembled at the Tonawanda factory on June 1st. The year is not specifically stamped. What we have left is the 'suffix code' which in this example is ED, a 1966 396cid/325hp for a manual transmission. Chevy used one to three letters of the alphabet to code the type of engine, transmission and vehicle into the suffix code. In that case you might see 'T0601ED 6A174373' stamped into the pad on the front passenger side of the block. In this example, 6A174373 decodes to 1966 Atlanta final assembly, and the last six digits of the VIN. Depending on the year and plant, the partial VIN could be stamped into a different area of the block; the flange edge of the rear of the block near the bellhousing mating surface, the rough cast area next to the oil filter and sometimes the stamping is found above the timing cover mating surface on the front of the block.

Beginning January 1, 1968 the federal government requested voluntary compliance of identifying major parts of a motor vehicle by inscribing or affixing an identifying number or symbol on major parts. As far as research has shown, Chevrolet did comply. by stamping a partial VIN on all engine blocks⁽¹⁾. Again, the location on the block may vary between the plants and years but one change was made in 1968. The GM division number ('1' for Chevrolet) was added to the partial VIN. A 1968 version of an Atlanta partial VIN stamping would 18A174373.

vs.

Beginning in late 1969 model year, 3-letter engine suffix codes were used on the engine pad. This example happens to be a September 22-built 1970 396 engine with a TH400 transmission as noted by the CTW suffix code.

The plant, date, and engine ID codes were stamped at the respective engine assembly plants while the partial VINs (when applicable) were stamped at the final assembly plant. Therefore the two stampings will have different fonts, character sizes, and in some cases will be stamped at different locations on the engine block.

There is another type of stamping found on some blocks. This is the 'CE' code. You might see something like this 'CE056789' on the front pad of the block deck on the passenger side. The 'CE' stands for 'Chevrolet Engine' but is often erroneously referred to as 'Counter Engine', 'Counter Exchange' and 'Crate Engine' was used on blocks that were warranty replacement engines. If a customer had problems with his original engine, while it was under warranty, it was replaced with an engine that was stamped 'CE' with a 6-digit number following it which serialized that particular engine. It's important to note that the 'CE' designation for replacement Chevrolet engines did not start until 1968 so any year designation in the engine number would be for 1968 and later. The CE block stamp year is the year the block was stamped and not for what year of car the block was destined for since a generic block for fitted engine could be used as a warranty replacement for any number of years' engines, applications, and for cars produced from any assembly plant.

Here you can clearly see the CE067997 stamping on the engine pad. This one produced in 1970 at Tonawanda with engine serial number 67997.

Here you can clearly see the CE173170 stamping on the engine pad. This one produced in 1971 at Tonawanda with engine serial number 73170.

Another CE stamping, this one is 066953 from 1970.

A calendar year 1973 replacement engine #356957

A calendar year 1973 replacement engine #367742

Warranty engines will be date stamped on the starter mount pad. Here T099 represents Tonawanda (T), September (09), 1969 (9)

Warranty engines will be date stamped on the starter mount pad. Here T099 represents Tonawanda (T), June (06), 1973 (3)

It's been reported that beginning in 1970, if more engines were needed at a given plant in a year than the range of sequence numbers allotted, the plant would re-use the numbers using the letter 'A' after the 'CE' and year designation. For example, Tonawanda was assigned the sequence range of 50,000 to 79,999 so if more engines were required the numbering would start over again at 50,000 but the 'CE' prefix would become 'CExA' where 'x' is the year such as CE0A50000.

It is believed this method of identifying replacement engines stopped after the 1975 model year. This is supported by a notation in a 1976 dated Chevrolet parts book, 'The engine plants are to stamp the serial pad of all current model service engines with the source, production date, and same type designation as stamped on a comparable production engine.'

Partial VIN stamping on engine blocks.

283 Chevy Engine Serial Number Location 2001 Honda Foreman Rubicon

Often referred to as a gang stamp because the partial VIN characters (or in this case a Flint engine plant stamp) was used to 'gang' the characters into one even line for stamping as opposed to each character being individually stamped.

Before a federal mandate that all engine blocks be stamped with a partial VIN, generally, only the 396 engines from 1965, 1966 & 1967 Chevelles along with the L79 engine blocks from 1965 & 1967 Chevelles were stamped with a partial VIN. These were done by hand and by individual character often resulting in some very strange looking engine pads. The partial VIN consisted of a single number representing the model year, a letter for the final assembly plant, and followed by the six-digit sequence number of the vehicle.

Beginning January 1, 1968, by federal mandate, all engine blocks would be stamped with a partial VIN consisting of a single number for the General Motors division (Chevrolet's number is '1'), followed by the same information as before; the model year, plant, and sequence number. General Motors standardized this procedure by using what's called a 'gang stamp' as shown in the photo above. Each individual stamped character was placed in a holder and secured before the engine block was struck by the employee responsible for doing this task. This holder allowed for consistency in the particular characters used and assured the partial VIN stamp was uniformly done from car to car. Even though some plants elected to stamp partial VINs on other locations beside the engine pad (such as the rough cast area by the oil filter boss or on the bellhousing flange), most plants for most years did stamp the partial VIN on the engine pad next to the Flint or Tonawanda engine assembly date and ID letters.

Chevy Engine Serial Number Identification

1970 Van Nuys example of the partial VIN stamped on the rough cast area by the oil filter.

1970 Atlanta example of the partial VIN stamped on the engine pad.

Not to say mistakes weren't made as the person responsible had to insure the numbers were changed for each vehicle as necessary. The plants employed a 'blank' stamp to obliterate a mistaken stamp so the corrected stamp could be applied.

⁽¹⁾ There is a question as to whether this date is accurate for federal mandate that engine blocks be stamped with a partial VIN. The information has been found on numerous Ford sites such as http://428cobrajet.org/id-block.html stating, 'Starting in 1967 for the 1968 model year, Ford began stamping partial VIN information on production engine blocks to meet the requirements of Title 49, United States Code, Subtitle VI, Part C, Chapter 331 (effective January 1, 1968).' Reading section 33107 'Voluntary vehicle identification number' sounds more like this was not mandated but was voluntary to comply as long as they did comply with sections 33102 and 33103. See http://uscode.house.gov/download/pls/49C331.txt or search the Internet for 'Title 49, United States Code, Subtitle VI, Part C, Chapter 331' for more websites with information.

MoPar forums searched seem to indicate that MoPar didn't follow the compliance until sometime midyear, 1968.

Transmission

Transmissions were also subject to replacement, be it just the case or the entire transmission. These will have a stamp something like 'CC' for Chevrolet Case or 'CT' for Chevrolet Transmission. The same information about partial VINs on engine blocks also applies to transmissions.